OCRACES

County of Orange (California)
Radio Amateur Civil Emergency Service


Orange County Sheriff's Department
Emergency Management Division


Home County/City/MOU Units Links Van Newsletters Net Assignments Mission Statement Member Expectations Baker to Vegas Winlink Visual Communications Emergency Supplies DC Connector
What Are ACS and RACES? FCC RACES Rules Contact Employment Volunteer Protection Act Forms

Powerpole Connectors

State of California OES prescribes the Anderson Powerpole as the standard dc power connector for use by State ACS/RACES personnel, and recommends its use by County and City RACES personnel as well. County of Orange RACES and other RACES groups throughout California and the United States have now adopted this connector. This standard, highly reliable connector allows quick and easy installation and substitution of radios, power supplies, batteries, and other equipment.

Either the 15-ampere (PP15), 30-ampere (PP30), or 45-ampere (PP45) sizes may be used, and any of those sizes mate with each other. The plastic parts are the same for all three sizes. The barrel area (which holds the wire) of the 15-ampere silver-plated contact is smaller than that of the 30-ampere contact, which is smaller than that of the 45-ampere contact, but the contact area is the same. The connectors dovetail together into a compact unit.

 

RED goes to +13.8 VDC and BLACK goes to ground. Housings should be mated according to the image above, viewing from the contact side (opposite the wire side), hood down, RED on the RIGHT, and TONGUE on the TOP ("RRTT"). Use a 3/32-inch-diameter roll pin, 1/4 inch long, to keep the housings from sliding apart.

Highly conductive silver-plated copper contacts allow minimal contact resistance at high currents. Self-wiping action on make and break keeps conducting surfaces clean. Contact dents keep connectors mated in high-vibration applications and provide quick-break, snap action upon disconnect.

Noncorrosive stainless-steel leaf springs maintain constant contact pressure—ideal for frequent connections/disconnections and intermittent overloading. Durable, high impact-resistant, polycarbonate housing with UL94V-2 flammability ratings comes in many colors for circuit traceability and coding.

Identical connector halves are genderless—making assembly quick and easy and reducing the number of parts stocked. Molded-in dovetails allow for a customized harness in a variety of configurations. When the connectors are disconnected, no metal parts are exposed.

The 15-ampere contacts are designed for 16-20 AWG wire, the 30-ampere contacts are designed for 12-16 AWG wire, and the 45-ampere contacts are designed for 10-14 AWG wire. The contacts can be soldered or crimped to wires. An expensive crimping tool (#1367G1) is available from Anderson. Other, less expensive, crimping tools are available from other sources. After a contact has been attached to a wire, it should be installed into the housing so that the housing spring mates with the underside of the contact.

To remove a contact from the housing, use Anderson insertion/extraction tool #111038G2. You may also substitute a very small blade (jeweler's screwdriver or X-acto knife) to depress the spring, allowing the contact to be removed.

Here are the Anderson part numbers:

15 A
Black
Red

Complete Connector
1395G1
1395

Housing Only
1327G6
1327

Contact Only
1332
1332

30 A
Black
Red

Complete Connector
1330G4
1330

Housing Only
1327G6
1327

Contact Only
1331
1331

45 A
Black
Red

Complete Connector
1345G6
1345

Housing Only
1327G6
1327

Contact Only
261G2-LPBK
261G2-LPBK

The connectors can be panel mounted with clamp receptacles, consisting of two aluminum plates (Anderson part #1462G1), notched to hold the plastic housings when they are dovetailed together.

The plastic housings come in other colors also. Red and black are suggested for standard dc connectors (red as positive and black as negative).

Anderson Power Products Web Site: https://www.andersonpower.com/us/en.html.